EXACTLY HOW TO INSTALL A TUB YOURSELF

Exactly How to Install a Tub Yourself

Exactly How to Install a Tub Yourself

Blog Article

Visit Link

We have stumbled on the article relating to Installing A Bathtub directly below on the net and felt it made sense to write about it with you here.


Installing A Bathtub
Installing a bath tub isn't specifically rocket science, but it does call for strong plumbing, woodworking, and sometimes, tiling abilities. Changing an old bathtub with a new one is additionally a moderately difficult task. If the old tub is readily obtainable, the job can move speedily; if you need to open a wall to get rid of the old tub and also place the new bathtub, the job is much harder. In either case, the job is within a home handyman's abilities, although you will require an assistant to move out the old bathtub as well as set in the brand-new one. Ensure you have certified on your own for the task and fit attempting it. As opposed to employing a professional to take control of a halfway-completed job, it is better to think about employing one prior to you begin. Opportunities are you may require a professional plumber to make tube links.
This short article will certainly assist you mount a new bath tub in your restroom if you have already bought a brand-new tub as well as don't require to change the plan of your previous water supply pipes.
Your devices and product checklist must comprise the following:
  • New Tub

  • Hammer

  • Pipe Wrenches

  • Prybar

  • Safety Glasses

  • Degree

  • Pliers

  • Adjustable Wrench

  • Putty Blade

  • Screwdriver

  • Cold Chisel

  • Measuring tape

  • Pipe Caps


  • Removing Old Taps


    If you require to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water supply. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The process of eliminating the existing faucets can be rather bothersome due to the restricted accessibility that is often the situation.
    Make use of a basin wrench (crowsfoot spanner) or a tap device to reverse the nut that connects the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will come from the pipelines. As soon as the supply pipes have been eliminated, make use of the same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the solitary faucets from turning during this process. When the faucets have been removed, the holes in the bath/basin will need to be cleansed of any old sealing compound.
    Prior to going on to fit the brand-new faucets, compare the pipe connections on the old faucets to the brand-new faucets. If the old faucets are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

    Suitable New Touches


    If the tails of the new taps are plastic, then you will need a plastic port to stop damages to the string. One end of the connector fits on the plastic tail of the tap and the other end offers a connection to the existing supply pipelines.
    If you require to fit a monobloc, after that you will certainly call for lowering couplers, which attaches the 10mm pipeline of the monobloc to the common 15mm supply pipeline.
    Next off, position the tap in the mounting hole in the bath/basin ensuring that the washers remain in area in between the faucet as well as the sink. Protect the tap in place with the manufacturer given backnut. As soon as the faucet is safely in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be linked by using corrugated copper piping or with normal faucet adapters. The previous type ought to be connected to the faucet finishes first, tightening only by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.

    Installing the Bath tub


    Making use of the two wooden boards under its feet, position the bath tub in the needed position. The wood boards are practical in uniformly spreading the weight of the bath tub over the location of the boards rather than focusing all the weight onto 4 little points.
    The following objective is to guarantee that the bathtub is leveled all round. This can be attained by inspecting the spirit level and also changing the feet on the bathtub up until the level reviews level.
    To install faucets, fit the bottom of the furthest adaptable tap connector to the proper supply pipe by making a compression sign up with; after that do the same for the various other tap.
    Switch on the water system as well as examine all joints as well as new pipework for leakages and tighten them if essential. Fill up the bathtub as well as also examine the overflow outlet and also the typical outlet for leakages.
    Finally, take care of the bath paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait until the bath tub has been made use of at least when as this will certainly settle it right into its final setting.

    Preparing for the Setup


    To start with, the supporting structure supplied with the bathroom should be fitted (if needed) according to the manufacturer's directions. Next off, fit the taps or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washer, it is fitted in between the bath as well as the faucets. On a plastic bath, it is likewise reasonable to fit a supporting plate under the faucets device to prevent stress on the bath tub.
    Fit the flexible faucet adapters to the bottom of the two taps making use of 2 nuts and olives (in some cases provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet opening, and then pass the outlet with the hole in the bathroom. Use the nut supplied by the maker to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
    Next off, fit completion of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which should be fitted inside the bath. Ensure you utilize every one of the provided washing machines.
    Connect the trap to the bottom of the waste outlet on the tub by winding the string of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the outlet. Link all-time low of the overflow tube in a comparable manner.The bathroom should now be ready to be fitted in its last placement.

    Tiling Around the Bath tub


    In the location where the bath meets the tile, it is required to seal the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bath as well as the tiling, causing issues with moisture and also feasible leakages to the ceiling listed below.
    You can select from a range of coloured sealers to assimilate your components as well as installations. They are offered in tubes as well as cartridges, as well as are capable of sealing spaces as much as a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to constantly load the bath tub with water before sealing, to allow for the movement experienced when the tub is in usage. The sealer can fracture rather very early if you do not take into consideration this motion before sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be made use of to border the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are additionally conveniently offered on the market. It is advisable to fit the floor tiles making use of water-resistant or water resistant adhesive and cement.

    A Step-by-Step Guide to Installing a Bathtub


    Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.



    But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.



    This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.


    Remove the Existing Bathtub


    To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.



    The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.


    Choose the Right Bathtub


    The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.


    Install the Plumbing and Ledger Board


    You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.



    Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.


    Install the Bathtub


    When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.



    Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.



    If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.


    Hook up the Plumbing


    Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.


    Install the Bathtub Surround


    A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.



    Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.



    If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.



    If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

    https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/


    How to Install a Bathtub

    I have been very taken with Tools You Need to Install a New Bathtub and I really hope you appreciated the new entry. Sharing is nice. Helping others is fun. Kudos for your time. Come back soon.




    Make An Appointment


    Report this page